BASIC OPERATION 18 Reception Transmission 7. CONTROLS, TERMINALS, AND DISPLAY Control Panel 14 LCD Display 15 Rear Panel 16 Other Components 17 Microphone 17 6. INSTALLATION AND CONNECTION (FOR MOBILE OPERATION) 10 Connection Diagram 10 Connecting an Antenna 10 Installing the Transceiver 11 Connecting the Power Cable 13 Connecting an External Speaker 13 5. INSTALLATION AND CONNECTION (FOR BASE STATION) Connection Diagram Connecting an Antenna Connecting a Ground Connecting the Microphone Connecting an External Speaker Connecting Headphones Connecting a DC Regulated Power Supply 4.
****** ****** CONTENTS PRECAUTIONS DOCUMENT CONVENTIONS 1. Indicates an exception or note related to the procedure. Indicates a hazardous situation that, if not avoided, will result in serious damage to the unit. Icons Indicates a hazardous situation that, if not avoided, will result in death or serious injury. Display Example Shows only the related indication. ****** ****** DOCUMENT CONVENTIONS Bold Typeface Indicates controls (keys, knob, etc.), terminals, and functions. e If any part of the transceiver excessively dirty, use a water- diluted neutral detergent to clean. e Do not use thinner, benzine, alcohol, or any solvent that might deform or discolor the transceiver. Cleaning Use a dry, silicone or soft cloth to clean the control panel and case. If the transceiver ever emits smoke or strange smells, immediately turn sit off and unplug it. If condensation forms on the unit, wipe or let dry. Condensation will cause the unit to malfunction. Moisture in the air will condense on the transceiver when you move it from a cold place to a warm place. x Use a 13.8 V DC regulated power supply to operate this transceiver. Such handling may damage or short-circuit the cable. Also, do not rewire the power cable with other extension cables. x Do not yank the power cable from its outlets. IOcm If the transceiver causes harmful interference to VCR or IV reception, move the transceiver away from the appliance. For ventilation, allow about 10 cm between the rear of the transceiver and the wall. X Do not place anything which might spill over on top of the transceiver. Also, avoid using the transceiver in an extremely dusty or humid environment. Do not expose the transceiver to direct sunlight or to source of heat.
****** ****** PRECAUTIONS n Do not open the transceiver case or touch no-user-serviseable components.
To obtain optimum performance from this transceiver, read this instruction manual thoroughly, and keep it for future reference. RIT RFIATT SQUELCH Instruction Manual Thank you for purchasing this A1-INCO transceiver. ****** ****** ALWCO COMMERCIAL HF SSB TRANSCEIVER DX-701 DIM OFFA-CN o.
Alinco edx 2 tuner manual transmission pdf#
Fully automated and powered by the Alinco transmitter this versatile rugged and weather-proof tuner features a full 200-watt PEP.Click here to download ALINCO DX-701 (01) PDF MANUAL Functionality 3.5 to 30 MHz with only 3 meters long 12 meter factor makes use of 1.6 MHz up. Harris uses a remote controlled vacuum condenser and roll coil so it can be retune and I have not finished remote AT-00 which once stored the configuration of another so apart from Harris my autotuned in the use of less power. High voltage and heat from diffusion flow is the bugaboo tuner and I had a layer burn on 0 watt on the ICOM AH2 when I once tried to fit too short a little 40 meters. I still need to delete memory manually and set when the primary settings ring has been deleted: half-pasted or parked next to a metal building. High-voltage capacitors are not so hard to overcome and if the board is properly laid out and the walk is big enough that should not be a problem. As long as you have not removed memory you can go back to the previous frequency and start talking but once deleted all memories are removed. I had the Alinco DX-8T so I bought the Alinco EDX-2 set it out and ran around 40 line up the side of townhouse and the upper hand and has made contacts all over the world from Iowa.I kicked up MFJ 31 foot vertical fiberglass Mast with 22 gauge spiral knocked around and laid out temp y radios and EDX-2 would put it vertically on any 160m long band that has a good performance. Note that you can not connect this type of coaxial coaxial to the output - you can use the ladder line if you want but it is highly designed to feed a string in opposition. I have a lot of broadcasts and sometimes I wonder if it just going to put six regular concerts in the bar lock with the things that are needed are not better.